لإن معظم الناس معندهاش وقت ……ده فلاش باك سريع و مراجعه مختصره عن ال antiscalant للي حابب يعمل refresh للموضوع ده لأن تمت مناقشته أكتر من مره علي الجروب .
حتلاقي ثلاث محاور أساسيه المراجعة دي مبنيه عليها:
1. تعريف مختصر لل antiscalant ووظيفته.
2. أنواع الscaling المتوقعه علي ال membrane.
3. الأعراض الناتجه عن الantiscalant السئ و طرق التغلب عليه عند ظهوره.
١- تعريف الantiscalant:

(polyacrylic acids, carboxylic acids, polymaleic acids, organo-phosphates, polyphosphates, phosphonates, anionic polymers)

٢- أنواع الscaling المتوقعه علي الmembrane:
نستطيع معرفه اذا كان الantiscalant جيد أم لا ببساطه عن طريق مراقبه مدي نجاحه في منع ترسيب الأملاح علي الأغشية مع الأخذ في الحسبان الإعتبارات الآتيه قبل الحكم علي جوده الantiscalant من عدمها:

*Lower temperatures reduce the solubility of mineral scales(the exception here is calcium carbonate scale formation which is enhanced when temperature increases)
*Dilution water should be hardness-free and preferably be of RO permeate quality. Diluted antiscalant/dispersants can become biologically fouled in the day tank depending on room temperatures and how much it has been diluted. A suggested residence time for a diluted solution is 7-10 days. Normally, undiluted antiscalant/dispersant solutions do not suffer from biological fouling.

*The chemical metering pump used for the injection of antiscalant/dispersant should be adjusted to maximize the frequency of injection. A suggested minimum stroking frequency is once every 5 seconds. Typical dosing rates of antiscalants/dispersants are 2 to 5 ppm.

*The design of the antiscalant/dispersant injection system into the RO feed stream needs to make sure that it is properly mixed before it enters the RO elements. The use of a static mixer is the most effective mixing method, but adds cost to the system. Most systems have the injection point just before the RO feed cartridge filter and rely on the cartridge filter residence time and RO feed pump agitation to affect the mixing.



و هو يعد من أشهر أنواع الscaling الذي تتعرض له الmembranes و يكون في شكل off-white powder.و من السهل تنظيفه عادا بواسطة acid قوي.

و له شكل غروي أو colloidal تظهر فيه الalumniosilicates في أول سلسله الممبرينات أو علي شكل ترسيب في أخر السلسه.. و هو صعب في إزالته.

و يأخذ شكل الجص أو الجبس (gypsum) و يتميز بشكل كريستالي له نهايات حاده جدا من الممكن أن تؤدي إليّ قطع سطح الmembrane. و يأتي تكون هذا النوع من وجود ال sulphate content ف المياه المستخدمه و هو أيضا يصعب إزالته.

و عاده ما يظهر بسبب طبيعه مياه الfeed التي تكون إما waste water أو agricultural leachate, و ذلك نتيجه ال phosphate high loading.

و يتواجد هذا النوع في ال second pass من محطات المياه ال brackish ذات نسبه الPH المرتفع لمعالجه ال boron الموجود في مياه الfeed , و ذلك عن طريق رفع ال PH أعلي من 9.5 في وجود الsodium hydroxide.

و يظهر في صوره كريستالات بيضاء لها شكل الشفرات و هو أيضاً نوع صعب التنظيف.

و يأخذ شكل إبري أو كريستالي needles or crystals و ممكن أن يقطع أغشية الmembrane و أيضا يصعب إزالته.
٣- الأعراض الناتجه عن الantiscalant السئ:
يلاحظ الآتي علي المحطه نتيجه عدم فاعليه الantiscslant:








